카페검색 본문
카페글 본문
-
스테인레스 강관 튜브규격 2010.08.28해당카페글 미리보기
low Mn Double melt Tube * 기계적 성질 Mechanical Properties Hardness(Rb) Yield Strenght (0.2% offset) Tensile strength Elongation (%) Reduction of area (%) ≥ 25ksi(172MPa) ≥ 70ksi(483MPa) ≥ 35 ≥ 50 ≥ 90 PIPE 국산화에 따른 표준안...
-
씨씨테크 UV 경화형 접착제 A-1311 (Chip-board 고정용 방습 접착제) .. 2006.12.25해당카페글 미리보기
Density at 25℃, g/㎤ 1.0396 Tested at 25℃ Physical Properties Contents Data Young's Modulus, MPa 13 Elongation, % >400 Tensile Strength, MPa 6.6 Degree of Cure Contents Data Gel Fraction, % >75 Shrinkage on Curing, % 3.56 * Cured in...
-
Differences between Cast Iron and Cast Steel 2019.12.24해당카페글 미리보기
vibration damping, good wear resistance, good machinability and low notch sensitivity. However, its tensile strength and elongation are very low. So, it can only produce some metal parts with low physical requirements. Requirements such...
-
슬개 건의 기능과 생체역학 - 반드시 정리해야... 2012.04.26해당카페글 미리보기
thus making limb and joint movement possible. Therefore tendons must be capable of resisting high tensile forces with limited elongation (36). The system with the most effective force transfer would be an inextensible load transmitting...
-
Medical Plastics Industry Set for Expansion over the Next Decade 2010.10.02해당카페글 미리보기
HCR were all examined. Both gamma and electron beam treatment lead to a rise in tensile modulus and a reduction in tensile elongation and tear strength. Ethylene oxide had minimal effects on the physical properties. Sterilization...
-
금속빠른학습 - 티타늄(Titanium)| 2010.05.31해당카페글 미리보기
Grade/ Ref. No. 0.2% Proof Stress min KSI 0.2% Proof Stress min MPa Ultimate Tensile Strength min KSI Ultimate Tensile Strength min MPa Elongation min % Density lb/in^3 Density gm/cc Weldability Rating Grade 1 25 170 35 240 24 .163 4.51...
-
Asahi Kasei Plastics Announces Soform™ For Automotive Interiors 2013.10.17해당카페글 미리보기
experience is desired. It is available in a wide range of physical properties (flexural modulus, hardness, tensile elongation, gloss) and moldable in any color and texture. Soform can be directly single-shot injection molded, replacing...
-
자동차산업 속의 폴리우레탄의 과거, 현재 그리고 미래(1부) 2009.03.09해당카페글 미리보기
불편함을 바로 느꼈을 것이다. 코코넛 화이버쿠션은 GM foam 표준으로 다시 평가되었는데 이 쿠션은 다소 장력(tensile)과 신장력(elongation)이 GM6293M 스펙에 미치지 못하는 것으로 나타났다. Tear strength는 표준으로 평가되었으나 컴프레션 셋은...
-
FLUOROSINT? MICA-FILLED PTFE MATERIALS 2011.06.15해당카페글 미리보기
Tensile Strength (psi) 1,100 1,500 1,450 2,100 Tensile Modulus (psi) 300,000 250,000 210,000 326,000 Tensile Elongation at Break (%) 10 50 90 40 Flexural Strength (psi) 2,200 2,000 2,500 4,000 Flexural Modulus (psi) 500,000 350,000...
-
프레임에 관한 소재 2009.10.15해당카페글 미리보기
티타늄의 경우에도 마찬가지다. 4.1.2. 티타늄의 최대 장점: 신장성(伸張性)과 인장강도(引張强度) Ti's Real Plus: Elongation and Tensile Strength 티타늄은 스틸이나 알미늄과 비교해서 밀도와 강성(剛性)에 있어서 2위를 기록하고 있다는 것을 알았다...